When an autoclave becomes a bottleneck in the laboratory, adding a second unit may seem like the obvious solution. But limited capacity is not always the real problem. In many cases, long cycle times are responsible for the low throughput.
Before investing in another autoclave, it is therefore useful to understand where the time within each cycle is actually being spent.
An autoclave cycle consists of several stages, including heating, air removal, sterilization, cooling and, depending on the application, drying. The validated sterilization phase should not simply be shortened to save time. Instead, improvements should focus on the stages surrounding it.
Depending on the load, significant time may be spent on:
- Removing air from the chamber and load
- Heating the load to sterilization temperature
- Generating and supplying steam
- Drying porous or wrapped materials
- Cooling liquids safely
- Preparing the autoclave for the next cycle
Identifying which of these stages is limiting throughput is the first step towards improving autoclave efficiency.
Start by analyzing your autoclave cycles
Rather than assuming which part of the process is responsible for long cycles, examine actual cycle data.
Modern autoclaves can record process information such as temperature, pressure and cycle duration. Reviewing several representative cycles can reveal whether most of the time is being spent during heating, sterilization, drying or cooling.
It is important to look at multiple cycles rather than one particularly slow run. Ideally, evaluate cycles over a representative period and compare different load types.
For example:
- Wrapped and porous loads: air removal and drying can contribute significantly to total cycle time.
- Liquid and media loads: heating and cooling are often important contributors.
- Waste loads: air removal and heat penetration can affect how quickly sterilization conditions are achieved.
- High-throughput laboratories: loading, unloading and turnaround between cycles can also become limiting factors.
Once the slowest stage has been identified, improvements can be targeted much more effectively.
1. Improve air removal
Air inside an autoclave is one of the factors that can interfere with efficient steam sterilization.
For sterilization to occur effectively, steam needs to reach the surfaces and materials being processed. Air pockets can reduce steam contact and make it more difficult for parts of the load to reach the required conditions.
This is particularly relevant for loads such as:
- Wrapped instruments
- Porous materials
- Textiles
- Certain waste loads
- Containers or loads with spaces where air can become trapped
Gravity-displacement or free-steaming processes remove air by allowing incoming steam to gradually displace it from the chamber. This can be suitable for relatively straightforward loads, but more complex or porous loads can make air removal more difficult.
A pre-vacuum system actively removes air before the sterilization phase. This can improve steam penetration and help the load reach the required sterilization conditions more uniformly.
If cycle records show that air removal and heat-up are consistently slow for porous, wrapped or complex loads, the air-removal method is therefore worth investigating.
2. Improve the drying stage
Drying is particularly important for wrapped instruments and porous materials.
A load may have completed the sterilization phase successfully while still containing residual moisture. For wrapped sterile materials, excessive moisture can make the load unsuitable for storage or immediate use and can increase the risk of contamination after removal from the autoclave.
Drying should therefore be treated as a distinct part of the cycle rather than simply an extension of sterilization.
Depending on the autoclave configuration, drying performance can be supported by:
- Post-vacuum stages
- A heated chamber jacket
- Controlled chamber heating
- Appropriate cycle programming
Vacuum helps remove steam and moisture from the chamber, while chamber heating can provide the energy required for remaining moisture to evaporate.
For laboratories processing substantial quantities of wrapped or porous materials, drying performance can have a considerable effect on both cycle duration and overall throughput.
3. Make sure liquid loads reach temperature efficiently
Liquid loads behave differently from instruments, glassware and other solid materials.
The chamber itself may reach the selected sterilization temperature before the liquid inside a bottle or container does. Larger liquid volumes can take considerably longer to heat throughout.
For this reason, the temperature of the chamber alone does not always indicate that the entire load has reached sterilization conditions.
Some autoclaves can use a load or reference probe positioned inside a representative container. The sterilization hold then begins according to the measured load temperature rather than relying solely on chamber temperature.
This approach can help ensure that the sterilization period starts at the appropriate point without unnecessarily extending every cycle to compensate for the slowest possible load.
4. Consider how steam is generated
Steam generation also influences how quickly an autoclave can reach operating conditions.
Depending on the autoclave design and installation, steam may be generated using:
- Chamber heaters
- An integral steam generator
- An external or central steam supply
An integral steam generator produces steam specifically for the autoclave and can support rapid steam availability between cycles. However, whether this improves throughput in practice depends on the existing system, load types and available utilities.
If a large proportion of cycle time is consistently spent reaching operating temperature, the steam supply and heating configuration are worth evaluating.
5. Look at cooling performance for liquid loads
For liquid sterilization, cooling can represent a substantial part of the total cycle.
Large bottles and dense liquid loads retain heat for a long time. They also cannot always be depressurized or cooled rapidly without considering the risk of boiling, container breakage or liquid loss.
Different autoclave configurations can use technologies such as:
- Cooling fans
- Water-cooled chamber jackets
- Controlled cooling systems
- Air ballast or support pressure
The appropriate cooling method depends on the type of containers, liquid volume, load configuration and process requirements.
If liquid cycles dominate the laboratory workload, reducing cooling time safely may provide a greater improvement in throughput than modifying another part of the cycle.
Don’t overlook turnaround time
The programmed autoclave cycle is not the only factor affecting daily throughput.
Consider the complete period between one load entering the autoclave and the next load starting. Additional time may be lost through:
- Waiting for loads to be prepared
- Loading and unloading
- Waiting for items to become safe to handle
- Selecting or configuring programmes
- Cleaning between particular applications
- Documentation and cycle release procedures
In a busy laboratory, relatively small delays between cycles can add up to a substantial amount of unused capacity over the course of a day.
Improving workflow around the autoclave may therefore increase throughput without changing the sterilization process itself.
When does a second autoclave make sense?
Optimizing cycle time does not mean that a second autoclave is never necessary.
Additional capacity may be justified when:
- The existing autoclave is operating close to capacity throughout the working day.
- Several departments depend on the same unit.
- Different load types regularly compete for available cycle time.
- Sterile processing requirements are increasing.
- Separating clean and contaminated workflows would improve operations.
- Redundancy is required to maintain operations during servicing or downtime.
However, if one particular cycle stage is responsible for most of the delay, addressing that stage may be more effective than immediately adding another machine.
A practical approach to improving autoclave throughput
Before changing the autoclave configuration or investing in additional equipment:
- Identify your main load types. Determine how much of the workload consists of liquids, media, waste, glassware, wrapped instruments or porous materials.
- Review representative cycle data. Analyse several cycles over a normal working period.
- Break the cycle into stages. Compare heating, air removal, sterilization, drying and cooling times.
- Find the main constraint. Focus on the stage that consistently contributes most to total processing time.
- Match the solution to the problem. Vacuum, improved drying, steam generation and accelerated cooling solve different problems and should not be treated as interchangeable upgrades.
- Measure the result. After making a change, compare cycle times and daily throughput again.
- Evaluate additional capacity afterwards. If throughput remains insufficient, a second autoclave may then be the appropriate solution.
Improve the process before increasing capacity
Reducing autoclave cycle time is not about shortening sterilization conditions simply to make a cycle faster. Sterilization parameters must continue to meet the requirements of the load, process and applicable validation procedures.
Instead, laboratories can look at the stages surrounding the sterilization hold.
For wrapped and porous loads, air removal and drying may deserve particular attention. For liquid loads, heating and cooling can be more significant. In other laboratories, steam availability or simply the workflow between consecutive runs may be the limiting factor.
Understanding where cycle time is actually being spent makes it possible to target improvements where they have the greatest effect, and to determine whether additional autoclave capacity is really necessary.
Our autoclaves
Explore our autoclaves here